Skip to main content
Mon–Fri: 8:00 AM – 6:00 PMCall Us
Luna Heating & Air logo
Heating

Heating Repair & Service in Weber, Davis and Salt Lake counties

Need expert heating repair and service in Weber, Davis, or Salt Lake counties? Luna Heating & Air provides fast, reliable solutions.

Restoring Heat and Safety Across Weber, Davis and Salt Lake Counties

Is your furnace constantly clicking on and off without actually warming the house, or are you waking up to freezing rooms and a strange burning smell coming from the vents? These mechanical failures and airflow restrictions will not resolve themselves, and ignoring them often turns a minor sensor issue into a cracked heat exchanger or a complete system breakdown. Since 2004, the team at Luna Heating & Air has been ready to diagnose and resolve these exact heating failures for homeowners across the region.

Warning Signs Your Heating System Needs Professional Repair

The System Constantly Starts and Stops

You notice the heating equipment kicking on, running for just a few minutes, and shutting off before the house reaches the temperature set on the thermostat. Mechanically, this usually means the system is overheating and tripping a high-limit safety switch, or a safety sensor is failing to read the flame. If ignored, short cycling puts massive strain on the blower motor and heat exchanger, turning a simple sensor cleaning into a catastrophic system failure.

Cold Spots and Uneven Heating

The living room feels like a sauna, but the back bedrooms are freezing while weak airflow barely trickles from specific vents. This points to underlying issues with the blower motor struggling to push air, a failing zone damper, or a system that has lost its heating capacity entirely. Living with uneven heating forces your equipment to run longer cycles to compensate for the cold rooms, driving up your utility bills and accelerating wear on the internal components.

Unusual Banging, Squealing, or Rattling Noises

Instead of the usual low hum of warm air, your heating cycles are interrupted by loud metal-on-metal scraping, high-pitched squeals, or a sudden boom when the system ignites. A squeal is typically a failing blower motor bearing, while a loud boom upon ignition means gas is pooling in the combustion chamber before finally catching a spark. Delayed ignition is a serious safety hazard that can crack the heat exchanger over time, and motor squeals mean friction that eventually leads to a seized motor.

Yellow or Flickering Burner Flames

If you look into your furnace sight glass, the flames should be a crisp, steady blue, but a lazy, flickering yellow or orange flame means you have a serious problem. A yellow flame indicates incomplete combustion, meaning the system is not getting the right mixture of gas and oxygen due to dirty burners or a cracked heat exchanger. Incomplete combustion produces carbon monoxide, making this a critical safety hazard that requires immediate professional diagnostic testing.

Thermostat Disconnect and Unresponsive Controls

You crank the thermostat up to seventy degrees, but the digital display stubbornly reads fifty-eight and the system refuses to engage. This disconnect often stems from a blown control board fuse, degraded wiring, or a failing thermostat unit that can no longer communicate with the primary equipment. When the brain of your heating system fails, the mechanical components sit idle, leaving your home completely vulnerable to dropping temperatures.

Constant Blower Operation Without Heat

You hear the fan running constantly, but the air coming out of the registers is room temperature or completely cold. This happens when the heating cycle fails to ignite, but the fan limit switch stays engaged or the thermostat is wired incorrectly. A technician needs to test the limit switches and the sequence of operation to find exactly where the ignition process is failing.

Common Causes of Heating Breakdowns in Our Area

Dirty or Corroded Flame Sensors

The flame sensor is a tiny metal rod that tells the gas valve a fire is actually lit and safe to maintain. In our dry, dusty environments, these sensors frequently build up a microscopic layer of carbon, preventing them from feeling the flame and causing the gas to shut off immediately. The solution involves carefully extracting the sensor, polishing it clean with specialized abrasive materials, and testing the microamp draw to ensure it is reading correctly.

Failing Hot Surface Ignitors

Modern heating systems use a hot surface ignitor that glows white-hot to ignite the gas, rather than relying on an old-school standing pilot light. Over thousands of heating cycles, the delicate material in the ignitor degrades, cracks, and completely fails to glow when called upon. Fixing this requires a technician to safely remove the fragile broken ignitor and install an exact factory replacement with the correct voltage to prevent an immediate burnout.

Overheating Blower Motors

The blower motor is the workhorse of your heating system, and when homeowners forget to change their air filters, the motor has to work twice as hard to pull air through the restriction. Over time, this causes the motor windings to overheat, the bearings to dry out, and the entire assembly to seize up permanently. Replacing a blower motor involves pulling the blower assembly, wiring in the new motor, and calibrating the fan speed to match your ductwork capacity.

Cracked Heat Exchangers

The heat exchanger is the metal shield that separates the toxic combustion gases from the clean air blowing into your living space. Years of expansion and contraction from heat can cause the metal to crack, especially if the system has been short-cycling or overheating due to poor airflow. Because a cracked heat exchanger leaks carbon monoxide into the airstream, it cannot be patched or repaired, requiring either a complete cell replacement or a new heating unit.

Tripped High-Limit Switches

Your furnace has a built-in thermometer called a high-limit switch that shuts down the burners if the internal temperature gets dangerously hot. Poor airflow from a clogged filter, collapsed ductwork, or a failing blower motor will cause this switch to trip repeatedly to prevent a fire. Once a limit switch trips enough times, it gets stuck in the open position and must be professionally replaced before the system will fire again.

What to Expect During Your Heating Service Visit

When you call Luna Heating & Air, you get a fully credentialed expert showing up at your door ready to diagnose the actual root cause of the failure. Our bilingual technicians carry NATE, EPA, and RMGA certifications, meaning we do not just guess at the problem by throwing expensive parts at it. We start by listening to your experience with the system, then dive into testing thermostat calibration, electrical draws on your motors, combustion chamber integrity, and gas pressures.

Once we pinpoint the failure, we have a blunt, honest conversation with you about the state of your equipment. We will show you exactly what failed, explain why it happened, and quote you the exact price upfront before any wrenches turn. If it is a simple repair, we will get the system running right then and there to restore your comfort and peace of mind.

If the system is older and the repair is costly, we will lay out the math on repairing versus replacing without any high-pressure sales tactics. As a Goodman equipment partner offering GreenSky Financing, we make sure you have all the options necessary to make the best financial and mechanical decision for your home. You stay in complete control of the repair process from the moment we arrive until the job is done.

Heating Repair & Service Coverage Across Weber, Davis and Salt Lake Counties

Because mechanical failures do not care about city lines, our trucks are dispatched strategically to provide fast, reliable diagnostics wherever you live in the region. We arrive well-equipped with the diagnostic tools and replacement parts needed to get your heat back on quickly.

Weber County: West Haven, UT, Ogden, UT, Roy, UT

Davis County: Clinton, UT, Syracuse, UT, Layton, UT, Kaysville, UT

Related Heating Services

Sometimes a repair visit uncovers a system that has simply reached the end of its lifespan, at which point we will guide you through Heating Installation & Replacement options that fit your home. On the other hand, if we catch a minor issue early and get it fixed, we highly recommend scheduling routine Heating Maintenance & Tune-Up services to keep the system running efficiently. Staying on top of maintenance is the absolute best way to prevent those late-night breakdowns from happening again.

Get Your Heating System Back Online Today

Living with a failing heating system is miserable, stressful, and sometimes downright unsafe for your family. You do not have to settle for cold rooms, weird smells, or a thermostat that feels like it is mocking you.

Let the experts at Luna Heating & Air diagnose the root cause and restore your comfort the right way. Reach out to our team today to schedule your heating repair visit.

Ready for comfort that lasts?

Schedule service with Luna Heating & Air — licensed, insured, and trusted across Northern Utah since 2004.